Search results

Sorry, no longer available... I have a brand-new radiator, ESR3687, which fits all Discovery I 1994-1999. Also the correct radiator for 1995 Range Rover Classic. Will probably fit earlier RRC, but I am not the expert. This is a factory original radiator, not aftermarket, and not a recore etc.

Could be a rocker arm. The rockers are aluminum with a steel cup "staked" into the rocker arm side which pushes on the pushrod. There seems to be a period of time somewhere late 1990's to around 2002 (or so) where bad batches of rocker shafts were built. What happens is the "staking" of the...

Have you checked what our trusted vendors can provide? One such that I have purchased O2 sensors from is RoverGuy, www.roverguy.com Look under "LINKS" ...

If you are changing O2 sensors on a D1, you need to determine if you have the early model sensors or the (somewhere around 1997) Advanced Evaporate Loss (AEL) system. The AEL vehicles can be recognised by the rectangular-shaped emission (charcoal?) canister on the passenger side of the engine...

Try to investigate if the coolant could be leaking DOWN from the intake manifold. The intake manifolds are more prone to leaks, and that could run down the back of the engine and seem to be coming from the head mating surface. If it is the intake, that would be a simpler task than the head...

For parts for your Rover, there are several places south of you in the New England area, including Rovers North in Vermont and Atlantic British in NY State that can provide new parts for you. In Ontario, towards Toronto you will find Dominic (mentioned above) at www.landroversalvage.ca who can...

Change the viscous unit. Readily available from vendors discussed on this forum...

D1 new radiator Ad removed 2009 (can't delete whole ad)

D1 Dog Guard STC8413 (SOLD!) Sorry, it has been sold.

Good service, good products... send the email and be patient for the response.

I have a pair of beige/tan ones, and no Disco for them any more... sold the truck a month ago. Contact me and we can work something out. SORRY, THEY HAVE BEEN SOLD!

This is a fairly easy DIY job. The most difficult part (IMHO) are the oil cooler connections. They can be corroded and difficult to loosen. Otherwise, the rubber hoses to the engine are straightforward, and the whole radiator basically lifts out after a few brackets are unbolted.

I have a brand-new factory original Discovery I (auto trans) radiator available here, however similar to what others have said, the cost was over $350. It is the real thing though... unfortunately it is in Ontario.

The crank, rods & pistons (as a set) from a 4.6 engine can be inserted into a 4.0 block, as the bare block is the same. You may have to verify that the crank throws don't touch the casting and maybe grind off some aluminum to avoid that, but the block is the same. For the ECU, it could be...

Yes, you should have no problem to fit them. Attaching points are in the body already. Are you getting the side panels (trim boards)? If not, you will need to cut holes in yours to expose the mounting points...

Or do nothing as stated by the local dealership. They said just bolt them on and go... but I do agree about cleaning them of any grease or such.

Might seem a stupid question... Genuine LR brake rotors for the D1 (FRC7329) have a black protective coating (paint??) on them. Does this coating need to be removed or scuffed off when the rotors are first installed? I have not been able to find any answers to this. The black does seem to...

If you are still looking for "local" sources, do you have any Partsource outlets (www.partsource.ca) there? This is a Canadian Tire spin-off, and they carry more product line than CT. They even have Land Rover listings. I purchased brake pads for my D1 there when I needed some in a rush... On...

Go somewhere to get the OBD-II codes read, as suggested. One common reason for the code is an Oxygen Sensor slowly dying. The CEL can light up and clear automatically, however as you have seen, it usually comes on again pretty soon!

Like he said ^^^ the LONG warm-up could be the thermostat. I had that about 3 years ago. It's inexpensive and EASY to replace. Buy the proper one, even from the dealer... really! As for the gurgling, maybe you need to top up MORE in the coolant tank. For your leaks, can you relate the...