Adjustable Panhard Rods
- Thread starter teledan
- Start date
Take a look at these Dan they seem to be a bit better quality that the once you used before on your previous batch, keep us posted.
[FONT="][FONT="]http://www.ruffstuffspecialties.com/catalog/34SET.html[/FONT][/FONT]
[FONT="][FONT="]http://www.ruffstuffspecialties.com/catalog/34SET.html[/FONT][/FONT]
d1Driver - I have thought about it but the only way I can see to do heims on both ends would be to bend up a brand new rod instead of using the stock one. There is not much room before the bend around the diff cover to weld a heim like I do on the other end. If I had a tube bender I would definitely try making one from a brand new piece of heavy tubing with joints (heims or otherwise) on both ends.
Jake - Sounds good man! Its looking like I will be doing another batch starting at the end of May (as soon as school ends). I'll let you know!
ArmyRover - Thanks!!!!
muger80 - I was looking at those too. The heims look very similar but they say that with the high-misalignment spacers they are 2" wide and the mounting bracket for the panhard at the frame side is 1.75" so I don't know if those will work. I like how they sell them as a kit though with everything you would need. I may send them a note just to confirm the width, the price is a bit more but it may be worth it since I would just be paying for shipping once. This is what I am thinking (just so you all know what you would be purchasing). I will be using High-misalignment spacers from Ballistic Fabrication and the heims, tube adapters and jamb nuts from Barnes 4wd
Jake - Sounds good man! Its looking like I will be doing another batch starting at the end of May (as soon as school ends). I'll let you know!
ArmyRover - Thanks!!!!
muger80 - I was looking at those too. The heims look very similar but they say that with the high-misalignment spacers they are 2" wide and the mounting bracket for the panhard at the frame side is 1.75" so I don't know if those will work. I like how they sell them as a kit though with everything you would need. I may send them a note just to confirm the width, the price is a bit more but it may be worth it since I would just be paying for shipping once. This is what I am thinking (just so you all know what you would be purchasing). I will be using High-misalignment spacers from Ballistic Fabrication and the heims, tube adapters and jamb nuts from Barnes 4wd
Hey Dan is there any chance we can get one of these made before mid April I'm trying to get the truck before the dweb Utah trip
muger80 said:
Here's a tip: Start shooting the bolts on the Panhard rod with PB Blaster now. The one I sent to Dan took me 10 minutes to pull off my parts truck. When I tried to pull the old one off my driving D1 it took me 4 hrs! The axle side bolt was rust welded/seized into the steel sleeve for the bushing. It took many hours of pounding and awkward cutting to finally get it out.
Dan makes a nice panhard rod, though. :applause:
I have a spare panhard laying around I think. Someone pay the shipping and I can send it to Dan to get him jump started.ini88 said:
fishEH said:
I will pay for shipping it out to him, IF he is willing to get started on them. I don't want to push him into making them if he is busy at the moment. It can be like a pay it forward thing and I will send him mine right after I install it.
It's up to you Dan. Let us know.
Hey guys. I appreciate the interest in these and I hope to be able to help you guys out, I unfortunately don't have the time right now to get any made up though. I am in school right now and working full-time AND I own a Land Rover (which is sort of like a full-time job in and of itself 
). As soon as the semester is over I should have some free time to get some of these done again.
). As soon as the semester is over I should have some free time to get some of these done again.
Dan I dont want to push you into making these but I have 37 panhard rods saved up since the last time you did this deal and 37 buyers at $300 each
hahahah justtt kidddinnggg
hahahah justtt kidddinnggg