Hello
In my great frustration to get my 95 4.2 running again I have decided to replace some of the ignition parts- so far its got new plugs, wires, cap, button,rotor. I just ordered what said distributor ignition module part number TR.STC 1184TRNM and we cant figure out where in the heck this...
Hello-
I have a new to me 95 lwb project vehicle that is having a few issues-
1.after the rovertym 3inch lift and suspension conversion it is very loud, popping, springing, boinging etc is this normal and I should just ignore or have it checked out?
2. Since I didnt buy a kit with one of those...
Hello
I have a new project 95 classic that has no hood cable and hood wont close- so I was thinking about some kind of latch to go on the sides of the hood- are there any that are bolt on able with no modification? or is it easier to re do the hood opener cable thing? ok also I have limited...
Ok so I have this 98 disco. The oil light starting coming on at idle, I figured easy enough and not a big enough problem to drive all the way up to see PT in fortwayne so I took it to my local guy who works on my big trucks for me and asked him to clean the oil pan screen and tube. He then says...
Ok so I just bought a softub 220 off of ebay and it is located about 10 hours away so Im wondering if I could squish it into the back of my disco which would be much more comfortable to drive than the cargo van- so has anyone else attempted to fit one in a disco?
Ok so I just bought a lovely 98 with power seats and the passenger seat is stuck almost up to the dash or actually my knees are... the switch moves the seat forward up down etc just not back- is there a way to move this sucker back manually- I have tried just pushing but to no avail.
Any advice?
A fantastic project truck at a reasonable price....
1989 Range Rover Classic
White
around 149K if the odometer works....
This is what has been done in the last two months or so-
new tie rod ends
rebuilt pitman arm
new procomp shocks
replaced shock towers
new starter
new fuel pump and wiring
new...
hello all- my 89 is having mysterious turn signal failure- I checked the fuse- that is the extent of my electrical knowledge- any advice- it is still cold here so doing hand signals is getting old.
Thanks
Hello-
Im getting ready to install a new steering shaft in my 96 and wondering if it is as easy of an install as it looks and if I need to get some kind of special lube for the end that attaches to the steering box. unfortunately I cannot get my wheels straight which the rave cd seems to say is...
Riddle me this.....
Ok so Im looking at some sliders etc- if the sliders are made of steel and they touch the body of the truck wont it cause the dreaded corrosion problems? or does painting/powder coating/rhino lining prevent this? what if the stuff rubs off? Im boggled.
Hello all-
I have a client that has been taken advantage of by this man Todd Montgomery from Greensburg Indiana- They purchased a lightweight for their son from him, they had no rover knowledge and were sold what was supposed to be a mint restored rover for 10k
this truck is not a 10 K rover-...
Ok so can someone explain how a three link suspension system works, pro's and con's, what's the big deal and what is the difference between that and a 4 link?
Thanks
Is there anyone running LPG in their disco here in the us? Ive found plenty of kits in the Uk but with the exchange rate etc- it makes the $$$ too much. Ive seen plenty of info for other vehicles but not much NAS D1's.
Ive got a set of 4 BFG AT's that are about 1 year old- they have a few nicks in the side part of the tread but other wise are brand new- I switched to bigger MT's- I wanted to keep these as a second set but I must finance my camshaft upgrade so I would like 75.00 each Im located in Indiana and I...
Ok- so I stupidly bought a set of steel rims off of ebay. I got a great price but now after a long ordeal no lug nut will fit. the manufacturer says I need a tapered seat lug nut to match the rover threads- is there such a thing? If not I guess I have some very shiny foot stools.
deeeeez nutssssssss! Ok the haynes book makes it look way too easy to remove the four bolts to release the drive shaft (s) however with them being down in a cupped area with other nuts around I cant get any type of wrench in there- any suggestions on nut size and removal? Im getting ready to...
This site uses cookies to help personalise content, tailor your experience and to keep you logged in if you register.
By continuing to use this site, you are consenting to our use of cookies.