Search results

looking for a couple as I just had mine quit and Id like to have another spare going forwards . Let me know what you have.

Just found one of mine is slight bent on an engine I’m putting together. Need one ASAP. let me know if you have e one.

I bought this for the engine. Pretty much everything else is available. Or buy the whole thing from me (minus engine). It’s green, auto, has manual front seats, no jump seats, relatively solid (C-pillar down to arch looks incredibly solid, not even any bubbled paint)...

Need the early plenum (pre 3.9) that doesn?t have the 3.9 logo cast into it...

Seems I can't find a verified full bolt pattern of the crank, dowel and bolt holes of the Buick 215 / RV8 anywhere, so I want to reverse engineer a ZF bell housing. Anyone have one they want to part with for beer money?

Am I right in thinking I need to search out a late D1 front cover for such an engine?

As title. Will need shipped to Louisville KY, but will be doing a road trip in a week or so heading to Houston and back, so can pick up on route...

As title, I need a load of trumpets for another project, will buy the base as well as they can sometimes be difficult to remove. Please give me a price plus shipping to 40165

Two things are wrong with the drivers seat - 1; the stitching from left to right between the front and middle pads is coming apart and needs re-stitching, and 2; the heated seat element needs replacing. Unlike most others, the black (p)leather has held up really well, with no cracking or wear -...

The wife's D2 needs a set of new tires at some point. If anyone has a really good set, and is within an hour or so of Louisville, or willing to ship, drop me a line.

I have an '03, and jut got a replacement box and after finally getting it in, have realized the bitch won't fit up to my hoses. The HP hose (the front-most one) on my '03 has two O-rings, and the remnants of the hose on my replacement box has just one O-ring. The "second" o-ring on my original...

Well, what I mean is I've figured out what is going on, but not "why"... Basically, for the past year or so, I've been struggling with power steering pumps. They all end up noisy, squeaking, and groaning. Ones that I saw coming off quiet running trucks would squeak and groan on my truck...

So, following on from http://discoweb.org/forums/showthread.php?t=90886 It seems the bearing on my AC pulley is a little rough. Not sure if this is why I lost the bolt or not, but I would like to swap this rather than the entire AC compressor (and having to drain and re-charge). Does anyone...

Something told me to go look over the disco today, and there it was, the bolt is missing. I grabbed the hub, and it slid right off. I suspect the belt was merely keeping it in place. What I can't quite figure out, is this just a standard M6 bolt? The shaft is tapped M6, but the pulley is also...

Anyone have a copy they can email me? I need to do a truck and can't find the copy of this I had before the VI site disappeared. I think I remember how to do it, but would like to glance at the guide once more to be sure...

Looking for a good PAS pump shipped to 40165. Absolutely must be quiet running and leak free - I swapped the original one that leaked and was squeaky for a junkyard one that was just even more squeaky and the wife had a fit... So now looking to trusted members of Dweb to hook me up. Thanks.

Applies to both inside, and outside handles. This suddenly started last week - the rear door, which has never shown any issues before, wouldn't open. It acted like it was locked. Cycling the lock showed that the actuator seemed to be operating inside the door, but wouldn't allow me to open the...

I've noticed this a few times on many discovery's, as it looks so out of place. Almost like it was a fudge to hold up a sagging headliner... So, I was in a junkyard today pulling a door harness out of a '99 (my '03 door harness had one broken wire, and 6 yes SIX others where the insulation was...

Well, my steering box has started playing up, weeping fluid from the input shaft, but more concerningly is that the "assist" works just fine when turning right, but turning left has a delayed reaction and makes the pump screech.... All the junkyards round here suddenly are empty of D2's, so...

PRICE DROP This is a straight roof rack, has all fixings (but one of the countersunk socket cap stainless screws has the (drive)end mashed up, so would benefit from being replaced - I'll aquire new ones for the buyer. Powdercoat is faded, and has a few patches of surface rust. Not holed...