Search results

Putting my KVT backpack rack up for sale. AFAIK it’s a little different from the standard backpack rack with a 4” high basket, aluminum flooring, and the standard Hi-Lift mount. Rack was purchased from original owner in May 2006. It has sat in the back of the garage since Dec 2009. The rack...

Can anyone tell me if there is a discernible difference in the two shafts? I know they carry two different part #s, i assume the 4.6 ZF pushes the TC back a little bit... I need to pick up a new one for my 04, but most places list only 99-04. prob gonna go with Tom woods or...

anyone know offhand what size those things are? not near the truck, nada on search...... gracias

http://cgi.ebay.com/ebaymotors/EATON-ELOCKER-ELECTRONIC-LOCKER-24-SPLINE-LAND-ROVER_W0QQcmdZViewItemQQhashZitem4399d29197QQitemZ290343522711QQptZMotorsQ5fCarQ5fTruckQ5fPartsQ5fAccessories are there any whispers of an elocker coming out? I don't really believe this.

My inane ability to strip/crossthread things continues, any words of advice on replacing the bung? I'm going to call around tomorrow to see how much $$ it would cost to just get a new one welded in.... im looking at reaming/retapping/helicoil-ing but my skill level in this specific area is...

Anyone running this stuff? I think i may throw it in the TC after an upcoming bearing/seal swap... http://www.redlineoil.com/products_gearlubricants.asp?categoryID=6&subCategoryID=16 Saw this old thread from the series forum but thats about it...

There appear to be two different styles depending on the VINs, the earlier ones are six point (seems like generic hardware) while the others are 12 points from what i can see on RN and AB. My 95 has the six pointers on the side i'll be swapping, are the later ones an "improvement" or are they...

I neglected and abused (mostly neglected) my little warn m8000 for six years and it finally went french on me and surrendered. The motor seized and its housing cracked (I assume water ingress freezing, but it could be a lot of things??.) shitty pic of said crack is attached. I have two...

can someone tell me if there is a generic spindle bearing out there?? Napa/timkin/skf equivalent?? Mine is fucked and i need the truck back ASAP thanks :banghead: http://www.roverparts.com/Parts/FTC861.cfm

title says it all. I'm not near the truck and have only worked on the PS manifold. If i can get away with not dropping the cats that would be stupendous. thanks

can this be done with the TC output housing in place? Noticed some leaking on the bottom of mah drum, time to take a peek in there

Does anyone know what this should run for a DI? I found a good re manufacturing company, but don't really have the time or space to swap the boxes myself... Shop manual states 1.4 hrs, is this accurate?

FYI; http://money.cnn.com/news/newsfeeds/articles/djf500/200803180122DOWJONESDJONLINE000060_FORTUNE5.htm (sorry if this is old news, i don't check the general forums that often)

Today i was going to put in a new MC for my left foot, some testing had indicated to me that the MC was going bad so i ordered a new one from AB, arrived in a Britpart box, corresponding to P/N ANR2186. I got everything swapped and hit a snag when i tried to attach the pipe nut to the MC, it...

Ive got an impact wrench and sockets (that's it) and was curious if it possible to get the bolts out with an extensions/universal joint combo. I'd like to know if its doable before i go out and drop some coin on some impact accessories and have it not work. How are you guys getting these things...

I literally just finished a 350 mile trip and for the last 60 miles had to deal with a sudden and somewhat severe overheating issue (in 31 degree weather). It started when i was accelerating and noticed that the tach had bounced up suddenly (like when the connection on the back of the alt. is...

Ive been reading up on the past threads about synthetic line and just had some questions. My steel line is kinked to hell and i'm looking to replace it with some synthetic (XMAS time). I've been drooling over the setup EE sells, but not the price tag.. Any recommendations on a vendor (i've only...

Just wanted to point out that KN filters for DIs are only $30 with free shipping right now, pretty good deal if you ask me... FYI http://www.amazon.com/K-N-33-2737-Replacement-Filter/dp/B00062Z0V6 Im not trying to make any technical claims, just for whomever happens to like KN.... (For $30 i...

I'm ordering a new driver for my Lisle set and was wondering if anyone knew off hand what size the race is, don't have any handy right now (google yield nothing wither).. im guessing a 2.995 or 3.180 thanks

anyone know of a decent DS shop around NoVa or maryland?? How much should it cost to get a rear DS rebuilt for a D1?? J