Search results

I am selling a set of four 16? steel wheels and tires. The tires are Interco Super Swamper IROK N/D in size 245/75R16 and are they mounted on GCR black steel wheels. They are a 5 on 6.5 bolt pattern (D90/110, Disco 1, RRC). They have less than 700 miles on them. I bought them in October of 2015...

1996 D1....Looking for an aftermarket rear bumper and the windshield finishing pieces. Thanks, -Len

Revived an old post....SOLD I have for sale a DAP/Bearmach Hidden Winch Mount for the RRC. It may fit a D1 but not 100%. It has been painted black. I also have the instruction sheet. $125.00 and I will deliver it to URE or I will meet you between Floyd, VA and Troy, NC. I am not in a position...

Looking for a windshield finisher set for a 1996 D1. Thanks, -Len

I need the black fuel pump relay that is mounted on the passenger side inner fender. It has two plugs. I don't see a part# on ours. Thanks, -Len

1996 D1 4.0 We are having an issue with a high idle on startup and a slight stumble when first driving. The high idle is always there on initial startup. It may or may not go up once the truck is warm and is re-started. The CEL is not on. Now it sounds like the fuel pump may be running when...

Our 1996 discovery 1 is not getting power to the abs pump. Did the diagnostics and I am getting a code 2-8. Here is the weird thing, the ABS light is not on now and I cannot clear the code. I've been searching but cannot find what I need. -Len

Genuine Land Rover Winch & Mount RTC9587AA Sold I have a Land Rover Genuine Parts Superwinch X6 winch and hidden winch mount. It is new and still in the factory crate. The part# is RTC9587AA. I understand it to be for a RRC/Discovery 1. The price was $500.00 now $450.00 OBO and the buyer is to...

for a Discovery 1. I would prefer new or like new. -Len

Does the 4.0 stepper motor (IACV)use a gasket and an o-ring, or does it use just an o-ring, or just a gasket? Thanks, -Len

Wondering if you can point me in the right direction? I am normally pretty good at figuring these trucks out, but this has me stumped. I have done some searches and still can't figure it out. Working on a 1995 LWB. The starter went bad and I replaced it with one out of a 1989 RRC. Now I am not...

1993 RRC LWB. A few months back I bought a nice used RRC radiator from one of the regular used parts sellers on this board(Note: It is NOT Will Tillery!). The radiator was supposed to fit our 1993 LWB, but the cooler line fittings are larger than the fittings on the radiator. I contacted the...

I don't know if you guys would be interested in this or not.....I'll try to post some pictures of the finished project if you are. We are working on our 1993 RRC LWB. My son and I picked up a 2-1/16" SunPro water temp gauge from Autozone and a $6.00 1/4" NPT tap from the local hardware store...

I'm lookin for a set of gutter mounts and load bars for a RRC. Thanks, Len

Any leads on a reasonably priced replacement? Thanks, -Len

Working on our 1995 RRC LWB.... I had an issue where the starter would turn over very, very slowly and the truck would not start. I checked the voltage at the battery, at the starter solenoid, at the small wire on the solenoid, and it all shower 12.something volts. Tried to jump across the...

Does anyone have a source for the Varta Mempac three pin 3.6volt 100mAh battery or an equivalent? I've done a little searching with no luck. Thanks, Len

I read an earlier post suggesting how to do this modification to a 1988 RRC using a 14 cux ECU. Has anyone actually done this conversion? If so, can you detail the operation? Thanks, Len

I'm looking for a heavy duty drag link for our 1988 RRC. Thanks, Len

I'm looking for a decent Series lift gate. Thanks, Len